Relocation

Once the WAZER has been set up and put through some amount of use, we do NOT recommend moving the WAZER off-site under any circumstances. There is NO guaranteed safe means of moving WAZER to another location. The protection and precautions put into the original packaging are extensive and hard to achieve.

With that said, we cannot stop anyone from moving a WAZER to a different location. We understand that over time any environment will change or move entirely, so businesses & users need to adapt. We have come up with a list of tips and checks to make sure any necessary WAZER relocation is as safe as possible for both the user and equipment.

The packing instructions are pertinent to movement out of the door. If you only need to shift WAZER across the room or to a different section of the building, the re-packing is not necessary. Please read the Short Distance Relocation instructions.

Meanwhile, we cannot emphasize enough: WAZER. Inc is not liable for any damages or issues caused by disassembly, relocation, and reassembly after the initial set up. We do not recommend relocating the WAZER after the initial installation.

Tools Needed:

Large Sealable Bags & Small Sandwich Bags
Cleaning Supplies to perform a Manual Full Tank Clean
4mm & 6mm Hex

Procedure

Short Distance Relocation

Part 1 - Main Unit

Turn Water Supply Off
Purge residual pressure from the water hoses by following the “Hose Disconnect Label” on the side of the window, or the procedure below
- Setup & Maintenance > Input and Output Check > Output > HP Valve. Allow the HP Valve check to finish.
- You will see a sudden gush of water from the nozzle followed by a diminishing stream. The residual pressure is fully purged after the stream stops.
- Disconnect the exterior high pressure hose from the Main Unit. Note that there will be residual water in the Hose.
Disconnect the Power Plug from the wall. Keep power cable and 24v Power Supply neatly near the Main Unit.
Disconnect Main Unit Signal Cable from the Pump.

5. If moving to a different water input and drainage, please disconnect the White Drain Hose. Note that there will be residual water in the Hose. Refer to the diagram below to disconnect the PTC fitting. Store the Drain Hose in a sealed bag during the move.

6. Drain the water in the tank and clean the tank of all used abrasive and other debris. Any abrasive in the machine will greatly increase the weight, please make sure to empty it completely. Specific instructions found here. (Link)

7. Re-install the Cut Bed using the Cut Bed Bolts and Cut Bed Springs. This way we do not lose any parts.

8. Remove WAZER from Wall Mounted Anchors. Keep hardware in a bag.

9. Empty the Abrasive Drawer of Abrasive. (Link)

10. Place the empty Abrasive Drawer back into the Main Unit.

11. For short distance relocation, you may start moving the Main Unit by grabbing the Bottom of the Hoop or side of the Leg Extension. The main unit weighs more than 100lbs when empty. Moving it regardless of distance, is strictly a two man job.

12. If the WAZER has the leg stand equipped, you can move it with two people. Please do not place the WAZER on anything with wheels while the Stand Kit is attached.

13. If the WAZER does NOT have the leg stand, you can move it by placing the WAZER on a cart with wheels. Refer to the Stand Leg manual and reverse the assembly process to disassemble the kit. Keep all hardware in a bag. (Link)

14. Move the Main Unit to the desired location and prepare for re-assembly and set-up.

Part 2 - Pump Box

Disconnect the Pump Box Power cable from the wall.
If moving to a different water input and drainage, please disconnect all water lines. Refer to the Push-to-Connect fitting instructions in the previous section.
With the Water Supply off, drain the Inlet Filter Canister.
- Remove the Filter Canister from the bracket. DO NOT attempt to do this step while mounted to the wall.
- Place the Filter Canister Drain Hose into a sink or bucket.
- Turn the valve until water starts coming out of the drain hose. You will notice that the wipers will start to remove the debris caught on the filter.
- After a few turns, the valve at the bottom of the Water Filter will open and the water will drain.
- Turn the valve to close it.
- Remove the Water Filter from the Inlet Hoses.
Please note that residual water will remain in the pump and water lines.
Remove any Input Water Adapters from the source. Store fittings in a bag.
Disconnect the Inlet Water Hose from the Pump.
At this stage, the Pump is disconnected from all Inputs & Outputs. The Pump Box can move freely under one condition -Do NOT tip the Pump on its side. The Vented Oil Cap is still installed, and if the Pump Box is not level at all times, Oil can spill. If you are concerned about an Oil spill, open the Pump Cover to swap Oil Caps. The Yellow Vent Oil Cap will allow Oil to spill during movement. Swap to the Red Cap to seal the Oil in the crankcase. Store the Yellow Vent Cap in a bag.

8. For short distance relocation, you may start moving the pump by grabbing to the bottom of the side plate. A Pump Box weighs more than 100 lbs. Moving a Pump Box, regardless of the distance, is a two person job. If using a platform with wheels to move the Pump Box, please remember to keep it level.

9. Move the Pump Box to the desired location and prepare for re-assembly and set-up.

Summary

Part 1 - Purge the Main Unit of water, debris, and abrasive. Move with 2 people. Grab the bottom hoop or leg extensions. NEVER transport the Main Unit with Leg Stand on a platform with wheels.

Part 2 - Disconnect all inputs and outputs. If necessary, transfer Water Lines to a new source in a clean sealable bag. Swap Oil Caps. Move with 2 people.

Ready to set-up the WAZER in it’s new location? The latest version of the User Manual will walk you through the process!

Long Distance Relocation

If you are looking to move the WAZER to a location that requires complete disassembly and manual/shipping transportation, please contact the Support Team.